Show your printer(s)

Anything goes! Cheap or expensive, FDM or SLA, DIY or Commercial.
User avatar
david.kiddell
Posts: 7
Joined: Thu Jun 15, 2017 7:28 pm

Re: Show your printer(s)

Post by david.kiddell » Sat Jun 24, 2017 11:22 pm

Started with a 2014 sunhokey when I came across Tom's Dolly project

Image

I think in that photo I was printing one of the X carriage parts. I was printing in ABS and had to use a brim to even hope of getting bed adhesion.

Anyway it's been a long road but I finally got my cables tidied altho power supply isn't mounted yet:

Image

Mega+RAMPS from Makerbase, didn't start smoking like my first set:

Image

I made some strategic upgrades vs Tom's design by going for an aluminum frame and a genuine E3D hot end.

Print quality is basically night and day. Sunhokey on left, Dolly on right:

Image

MIKEYMCC
Posts: 3
Joined: Fri Jun 16, 2017 1:37 am

Re: Show your printer(s)

Post by MIKEYMCC » Thu Jun 29, 2017 1:22 am

This is my Dolly but to be honest it is becoming an actual MK2S. I now have an original Prusa frame, I bought a Rambo Mini board and I am waiting for a MK42 clone to install.

Image

Image

Phil-f
Posts: 1
Joined: Tue Jul 04, 2017 8:20 pm

Re: Show your printer(s)

Post by Phil-f » Tue Jul 04, 2017 9:14 pm

Hictop 3dp-17, Ikea LACK enclosure. This is my first 3d printer, I had big plans but for now I am happy that it will print fidget spinners. Bought this off of Amazon hoping I would get lucky and get something that worked ok, I was very wrong.
Thanks for looking!
Hictop3dp17.jpg
Hictop3dp17.jpg (118.3 KiB) Viewed 899 times


kleingeist
Posts: 34
Joined: Wed May 24, 2017 11:51 am

Re: Show your printer(s)

Post by kleingeist » Tue Aug 01, 2017 2:01 pm

I started with a Reprap Neo, shortly followed by a Trunigy Fabrikator (discount decision) and I am now pretty satisfied with my custom printer.
Attachments
IMG_20170801_135347_RAW.jpg
d³ custom printer
IMG_20170801_135347_RAW.jpg (1.41 MiB) Viewed 793 times

Peter Bermingham
Posts: 13
Joined: Thu Jul 06, 2017 6:00 pm
Location: Warracknabeal Victoria Australia
Contact:

Re: Show your printer(s)

Post by Peter Bermingham » Sat Aug 05, 2017 2:10 pm

Started with an Anet A8 then a CTC i3 then a Cocoon Create (Wanhao duplicator i3 plus) and now a Prusa i3 MK2s next up is a "Dolly" :D
The Prusa i3 MK2s
IMG_0896.JPG
IMG_0896.JPG (1.73 MiB) Viewed 766 times
The Anet A8 with a Cocoon Create print mat
IMG_0897.JPG
IMG_0897.JPG (1.6 MiB) Viewed 766 times
The Cocoon Create/Wanhao duplicator i3 plus
IMG_0895.JPG
IMG_0895.JPG (1.75 MiB) Viewed 766 times

User avatar
DavidMcCormack
Posts: 1
Joined: Mon Jul 24, 2017 8:27 pm

Re: Show your printer(s)

Post by DavidMcCormack » Wed Aug 09, 2017 4:07 pm

My 101hero which I have had for a few months and is still working. Not the best printer in the world but it does print. :D
20170809_150029.jpg
20170809_150029.jpg (2.18 MiB) Viewed 743 times

And my Anet A8 which I picked up in the last 2 weeks. It was printing fine until an issue with the y-axis switch port on the main board put it out of commission. Currently waiting on a new board :?
20170809_150039.jpg
20170809_150039.jpg (1.79 MiB) Viewed 743 times

BoriSpider
Posts: 5
Joined: Wed Jun 21, 2017 12:55 am

Re: Show your printer(s)

Post by BoriSpider » Thu Aug 10, 2017 9:08 pm

My first printer plus my first KickStarter by Billy Zelsnack.

ImagePrintxel 3D Printer by jendave3, on Flickr

The PrintXel was replaced by a ZeGo bot Mini delta.

ImageIMG_20160616_122636 by jendave3, on Flickr

Just need to hook it up to a RPi3 so I don't have to move my laptop between rooms when I want to print. Maybe even upgrade to a SmoothyWare board.

RayJohnson
Posts: 1
Joined: Sat Aug 12, 2017 6:18 pm

Re: Show your printer(s)

Post by RayJohnson » Sun Aug 13, 2017 12:52 am

My first printer, built in early 2013, is this Prusa I2. It has been my go- to work horse as it keeps churning out the prints. It was built from scratch using printed parts from NW Reprap and hardware from McMaster-Carr. It uses a homemade Gen7 controller with Teacup firmware. The controller parts were purchased from Digi-Key Electronics. The whole tally including the 30amp power supply was around $ 725.00 which at the time was cheap for a 3D printer. It currently uses a aluminum heat bed heated with a 180watt silicone pad heater. The heatup time from room temp to 220 is 6-7 minutes. The hot end is a J-Head Mk V from hotends.com for 3.00mm filament. I use Pronterface loaded on the Raspberry PI to run the prints from a USB stick. I take great pride in keeping my electronics and wiring nice and tidy.
p1.jpg
p1.jpg (784.66 KiB) Viewed 719 times
p2.jpg
p2.jpg (831.71 KiB) Viewed 719 times





I built this one a year later. It uses a Ramps 1.4 controller w/ Marlin, E3D Chimera , aluminum bed w/220 Watt silicone pad heater and a RepRapDiscount.com Full Graphic Smart Controller. Most prints are from the SD Card. It is powered by a Meanwell 50amp 12vdc power supply. The inverted Gregs Wade extruders are perfectly suited for the dual 1.75mm bowden setup. It is such a reliable printer that I don’t think twice before starting 24+ hour prints. And, as you can see, my compulsion for wire organization extend to this new printer.
h1.jpg
h1.jpg (817.95 KiB) Viewed 719 times

User avatar
PauloMateiro
Posts: 11
Joined: Wed May 24, 2017 1:33 pm

Re: Show your printer(s)

Post by PauloMateiro » Fri Aug 18, 2017 11:29 am

Well, here is mine.

Please be gentle... :mrgreen:

Image

Flyingbear P902.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest