Search found 232 matches

by Moorviper
Thu Dec 06, 2018 12:41 am
Forum: Software
Topic: Dolly MK52 upgrade
Replies: 5
Views: 105

Re: Dolly MK52 upgrade

check this video before buy the india one:
https://www.youtube.com/watch?v=zkHT9Y0aoEs
by Moorviper
Wed Dec 05, 2018 12:59 pm
Forum: Software
Topic: Dolly MK52 upgrade
Replies: 5
Views: 105

Re: Dolly MK52 upgrade

lol i had the opposite problem
I only found the 12V versions :D
as example
https://orballoprinting.com/en/home/186 ... &results=1
by Moorviper
Mon Dec 03, 2018 9:13 pm
Forum: Hardware
Topic: MK42 @24V (Orballo Printing)
Replies: 1
Views: 254

Re: MK42 @24V (Orballo Printing)

No burned traces.
the heating power is a little more than doubled.
22-100°C in 2,5 Minutes
by Moorviper
Mon Dec 03, 2018 4:38 pm
Forum: Hardware
Topic: MK42 @24V (Orballo Printing)
Replies: 1
Views: 254

MK42 @24V (Orballo Printing)

2018-12-03 16.28.40.jpg
2018-12-03 16.28.40.jpg (87.38 KiB) Viewed 254 times
wired for 24V 1.8 Ohm. 2+ Ohm would be better but it should do the job. (3.6 would be great)
@12V it was 1 Ohm so now it is doubled the power
by Moorviper
Mon Dec 03, 2018 12:35 am
Forum: 3D Printers
Topic: Show your printer(s)
Replies: 52
Views: 7628

Re: Show your printer(s)

2018-12-03 00.34.48.jpg
2018-12-03 00.34.48.jpg (70.06 KiB) Viewed 152 times
A total nightmare -> no working printer :-(

the one one the left brocken pinda holder after cleanup
2018-12-03 00.23.18.jpg
2018-12-03 00.23.18.jpg (73.99 KiB) Viewed 152 times
2018-12-03 00.34.54.jpg
2018-12-03 00.34.54.jpg (168.58 KiB) Viewed 152 times
the one in the middle is cannibalized :D


the the right one is not finished yet :-/
by Moorviper
Sat Dec 01, 2018 1:19 am
Forum: Software
Topic: MK42 alignment on a custom frame
Replies: 0
Views: 54

MK42 alignment on a custom frame

This is what i changed to get the MK42 aligned on my printer.
These are the set screws within the firmware:
Bildschirmfoto 2018-12-01 um 01.10.26.png
Bildschirmfoto 2018-12-01 um 01.10.26.png (51.83 KiB) Viewed 53 times
Bildschirmfoto 2018-12-01 um 01.11.17.png
Bildschirmfoto 2018-12-01 um 01.11.17.png (239.49 KiB) Viewed 53 times
Bildschirmfoto 2018-12-01 um 01.11.53.png
Bildschirmfoto 2018-12-01 um 01.11.53.png (114.36 KiB) Viewed 53 times
by Moorviper
Fri Nov 30, 2018 7:19 pm
Forum: Help requests / Purchasing assistance
Topic: First print problems with my brand new dolly (i3 clone)
Replies: 4
Views: 98

Re: First print problems with my brand new dolly (i3 clone)

looks strange but you are too much away from the heatbed with your noozle. it looks like the steps aren't set correct. btw your printsurface looks like "bluetape". This is the same i started with. With similar results ... Then i used and use allready a PEI sheet from prusa. The sheet which is delive...
by Moorviper
Fri Nov 30, 2018 2:19 am
Forum: Hardware
Topic: Prusa MK 52 hole layout
Replies: 4
Views: 92

Re: Prusa MK 52 hole layout

the screenshots are of the 24v version i hovered the mounting holes so you can calculate the distance between the points

hovered 3 points x and 3 points in the y direction.

not totally precise but i think prusa used smooth numbers
by Moorviper
Thu Nov 29, 2018 1:06 pm
Forum: Hardware
Topic: Prusa MK 52 hole layout
Replies: 4
Views: 92

Re: Prusa MK 52 hole layout

btw which one do you need the 12v and 24v versions are different
by Moorviper
Thu Nov 29, 2018 12:41 pm
Forum: Hardware
Topic: Prusa MK 52 hole layout
Replies: 4
Views: 92

Re: Prusa MK 52 hole layout

I have a heatbed carriage for the mk52 at home i can take some measurements this evening. edit: it is on github: https://github.com/prusa3d/Heatbed_MK52_magnetic Bildschirmfoto 2018-11-29 um 12.43.29.png Bildschirmfoto 2018-11-29 um 12.46.04.png Bildschirmfoto 2018-11-29 um 12.46.14.png Bildschirmfo...