Search found 9 matches

by anthonyyaghi
Sun Oct 21, 2018 10:04 am
Forum: Help requests / Purchasing assistance
Topic: Need desperate help with tmc2130 :(
Replies: 12
Views: 4745

Re: Need desperate help with tmc2130 :(

Thank you, filament is ok now but another problem appear :roll: I doubled the step/mm settings since the DRV8825 have 32 microstep double the 16 of the A4988. But the problem now is that the stepper motor of the extruder doesn't work with the new setting it just make buzzing sounds but doesn't turn....
by anthonyyaghi
Sat Oct 20, 2018 6:09 pm
Forum: Help requests / Purchasing assistance
Topic: Need desperate help with tmc2130 :(
Replies: 12
Views: 4745

Re: Need desperate help with tmc2130 :(

Ok so finally I got a new RAMPS board with an arduino mega instead of the MKS board and everything is working fine. Thanks a lot Stefan :) Btw I am facing a new problem the filament keeps on breaking inside the nozzle, but the filament I have has been sitting in not so optimal storing conditions for...
by anthonyyaghi
Thu Oct 18, 2018 9:30 pm
Forum: Help requests / Purchasing assistance
Topic: Need desperate help with tmc2130 :(
Replies: 12
Views: 4745

Re: Need desperate help with tmc2130 :(

Ok so there is 3 jumpers underneath each driver I previously had removed all of the for the 2130. I noticed that if I place them back the DRV8825 is there a certain configuration for the jumpers that might be preferable with the tmc2130 ?
by anthonyyaghi
Thu Oct 18, 2018 9:08 pm
Forum: Help requests / Purchasing assistance
Topic: Need desperate help with tmc2130 :(
Replies: 12
Views: 4745

Re: Need desperate help with tmc2130 :(

This is getting ridiculous, I re-checked everything for a short circuit or a bad connection and I am not an idiot I work with robotics and embedded systems a lot I know what I am doing but everything seems fine. I bought some new DRV8825 (only ones I could find) and installed them instead then chang...
by anthonyyaghi
Wed Oct 17, 2018 9:51 pm
Forum: Help requests / Purchasing assistance
Topic: Need desperate help with tmc2130 :(
Replies: 12
Views: 4745

Re: Need desperate help with tmc2130 :(

Hi Anthony, A value like "0xFF:FF:FF:FF" suggests a connection issue. Look at wiring, solder, etc. -Stefan Ok So I check all the wiring again but couldn't find any problem. I did a fresh configuration and only changed what is necessary to run the TMC2130, but as soon as I connect to the printed I g...
by anthonyyaghi
Wed Oct 17, 2018 5:53 am
Forum: Help requests / Purchasing assistance
Topic: RAMPS 1.4 and Mega2650 upgrade problems
Replies: 12
Views: 4709

Re: RAMPS 1.4 and Mega2650 upgrade problems

I am having problems with the tmc2130 as well, they are not working yet but here's what could be wrong.
Are you using the default pins for communication with the tmc2130 (SDO, SDI, select...) ? Because the LCD and SD card uses some of them as well so there migh be some conflict.
by anthonyyaghi
Tue Oct 16, 2018 11:23 am
Forum: Help requests / Purchasing assistance
Topic: Need desperate help with tmc2130 :(
Replies: 12
Views: 4745

Re: Need desperate help with tmc2130 :(

Hi Stefan, Thank you for the continuous help I appreciate it :) sorry I am not able to reply quickly because I am working all day long. I checked the wiring quickly they seem to be ok. I am not able to execute "M500" I the EEPROM is disabled in the marlin configuration. I will fix it today and reche...
by anthonyyaghi
Sun Oct 14, 2018 8:35 pm
Forum: Help requests / Purchasing assistance
Topic: Need desperate help with tmc2130 :(
Replies: 12
Views: 4745

Re: Need desperate help with tmc2130 :(

Hi Stefan, Yes I have my board in the open and every driver has a heatsink. I will try setting the current values then resetting the EEPROM as you suggest. Btw I tried a M122 and I am getting this output: READ: Driver registers: X = 0x00:00:00:00 READ: Y = 0xFF:FF:00:00 READ: Z = 0x00:00:7F:FF READ:...
by anthonyyaghi
Sun Oct 14, 2018 9:06 am
Forum: Help requests / Purchasing assistance
Topic: Need desperate help with tmc2130 :(
Replies: 12
Views: 4745

Need desperate help with tmc2130 :(

Hello everyone, I recently burnt a driver on my Tevo tornado MKS base board. I decided to go for an MKS gen 1.4 and tmc2130 for a change and less noise but they are making my life hell :( I tired to follow several guides and read the (minimal) documentation of the board, but I can't get them to work...