Search found 47 matches

by bentech4u
Sun Mar 18, 2018 6:33 am
Forum: Hardware
Topic: Auto Bed Leveling, adding to existing working printer
Replies: 0
Views: 737

Auto Bed Leveling, adding to existing working printer

HI my printer was working as normal with Z-endstop switch. I would like to add auto-bed leveling to this, for that i purchased PNP inductive sensor, which is connected to RAMPS1.5 with resistor voltage drop circuit, i measured the voltage using a multimeter when it triggered, the voltage goes to zer...
by bentech4u
Thu Oct 19, 2017 11:35 am
Forum: Hardware
Topic: Creating Prusa(toms Dolly) design using aluminium frame. end stop question
Replies: 55
Views: 7319

Re: Creating Prusa(toms Dolly) design using aluminium frame. end stop question

HI,

anyone please recomend best slicer,

normal Slicer or prusa Slicer is better?

also send me the best combination for PLA print.

Regards,
Ben
by bentech4u
Wed Oct 18, 2017 12:12 pm
Forum: 3D Printers
Topic: Anyone successfully build Smartrap Mini
Replies: 1
Views: 1198

Anyone successfully build Smartrap Mini

Hi All, i would like to build the Smartrap mini and there no much information on the internet about that printer. only I found some videos that too different language (not English). https://www.youtube.com/watch?v=MfM5OHYkWk4&list=PLOC55t9dY7y9V-wKPW3eSvyRtIbhhQFxa If anyone successfully assembled t...
by bentech4u
Sun Oct 15, 2017 1:01 pm
Forum: Hardware
Topic: Creating Prusa(toms Dolly) design using aluminium frame. end stop question
Replies: 55
Views: 7319

Re: Creating Prusa(toms Dolly) design using aluminium frame. end stop question

HI,

if the belt is the case I would say Y axis is average tight and X axis is bit more light. will the X axis belt tightness produce this effect?

Regards,
Ben
by bentech4u
Sun Oct 15, 2017 9:37 am
Forum: Hardware
Topic: Creating Prusa(toms Dolly) design using aluminium frame. end stop question
Replies: 55
Views: 7319

Re: Creating Prusa(toms Dolly) design using aluminium frame. end stop question

HI Thanks, I always used to level with paper as auto bed leveling is not configured. I will try to put closer to the nozzle and will try. . If you fix the bottom layer and still have some slanting, you should check that all axes are square to one another. This can be kind of hard to do with any squa...
by bentech4u
Sun Oct 15, 2017 7:20 am
Forum: Hardware
Topic: Creating Prusa(toms Dolly) design using aluminium frame. end stop question
Replies: 55
Views: 7319

Re: Creating Prusa(toms Dolly) design using aluminium frame. end stop question

Thanks a lot, i have connected the FAN directly to 12 V and the jamming issue solved. again another 2 issues 1. the first layer is not correct(before for ABS also i had this issue and that got solved by increasing headbed heat) 2. total object is little slanting to Y MIN direction For the first issu...
by bentech4u
Sat Oct 14, 2017 8:53 pm
Forum: Hardware
Topic: Creating Prusa(toms Dolly) design using aluminium frame. end stop question
Replies: 55
Views: 7319

Re: Creating Prusa(toms Dolly) design using aluminium frame. end stop question

HI, i did the same only, heated up to 240 and cleared all the ABS. and many times i cleaned the nozzle and eating barallel manually by opening it , again the same thing. my cooling fan on e3d clone is only turning on while i start printing..is that normal behavior? heat sink on top of heating barall...
by bentech4u
Thu Oct 12, 2017 9:35 am
Forum: Hardware
Topic: Creating Prusa(toms Dolly) design using aluminium frame. end stop question
Replies: 55
Views: 7319

Re: Creating Prusa(toms Dolly) design using aluminium frame. end stop question

HI

i got my PLA spool and when i tried to extrude, filament is always jamming on hotend. removed, cleaned everythin. again same.

i was using temperature of 200 C and using the extrude button on printrun to extrude.
by bentech4u
Tue Oct 10, 2017 6:55 am
Forum: Hardware
Topic: Creating Prusa(toms Dolly) design using aluminium frame. end stop question
Replies: 55
Views: 7319

Re: Creating Prusa(toms Dolly) design using aluminium frame. end stop question

HI

thanks all, Almost everything is working now.and now i am getting perfect prints.
by bentech4u
Mon Oct 09, 2017 7:22 am
Forum: Hardware
Topic: Creating Prusa(toms Dolly) design using aluminium frame. end stop question
Replies: 55
Views: 7319

Re: Creating Prusa(toms Dolly) design using aluminium frame. end stop question

HI, My PLA is on the way and it will reach soon, meanwhile, i got sample ABS from one local store, i cant wait without trying that :) i have changed the value and printed one 20 mm cube, all the measurements are correct now. But the print has some issues, i cannot able to explain much, and the total...