Search found 7 matches

by Raider1284
Tue May 22, 2018 8:02 pm
Forum: Software
Topic: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds
Replies: 196
Views: 35928

Re: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds

Has anyone figured out how to get the mk3 firmware working on the ramps clone? If you have, please let us know how you were able to get it working, and what changes to the firmware you had to make. I have seen quite a few forked versions that claim to work but I havent found any yet that compile suc...
by Raider1284
Fri May 04, 2018 8:26 pm
Forum: Software
Topic: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds
Replies: 196
Views: 35928

Re: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds

Hello, I have just upgraded to a Mk42 heatbed and installed the firmware, however It is not working at all. I have Ramps 1.4. When the printer is on, the Z motors are constantly enabled, with Y and X disabled. When I connect through repetier I get: 09:08:04.730 : No start signal detected - forcing ...
by Raider1284
Thu Apr 26, 2018 12:39 am
Forum: Software
Topic: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds
Replies: 196
Views: 35928

Re: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds

Hello everybody, So this https://github.com/kfazz/Prusa-Firmware/tree/MK3_Ramps is what y'all are talking about or where can I find the latest version of the "RAMPS Prusa Firmware"? Also, a bit of a OT question (I promise it's just a little one! :P ): I just got the electronics (Mega 2560 + RAMPS) ...
by Raider1284
Mon Mar 12, 2018 5:22 pm
Forum: Software
Topic: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds
Replies: 196
Views: 35928

Re: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds

what are the hexagon nut looking things in front of some of the wiring holes? I'm not sure which bit you mean, but if you can annotate the image, I'll be able to help :). sorry i should have done that from the get go. I added an arrow to the part I was asking about: https://i.imgur.com/F2fK2wb.png
by Raider1284
Fri Mar 09, 2018 9:09 pm
Forum: Software
Topic: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds
Replies: 196
Views: 35928

Re: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds

Is the stl for that mks 1.4 case available by chance? Its exactly what im looking for and has the mount points to attach to 3030 extrusions! I havent been able to find a good one for extrusions on thingiverse. Thanks in advance! Sorry for the slow reply, I've only just seen this. I'll check to see ...
by Raider1284
Thu Mar 01, 2018 1:35 am
Forum: Software
Topic: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds
Replies: 196
Views: 35928

Re: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds

Sorry, i meant to reply to your previous post but never got round to it. Presumably therefore, you figured out the problem? what was it? RAMPS and the MKS boards don't have any digipot type hardware for setting stepper currents in firmware. This means that the Quiet Mode / High Power settings in th...
by Raider1284
Thu Mar 01, 2018 1:33 am
Forum: Software
Topic: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds
Replies: 196
Views: 35928

Re: Prusa firmware for RAMPS Prusa i3 clones with MK42 beds

Hello, Does somebody know how to get run RepRapDiscount Full Graphic Smart Controlle? I have tried uncomment #define DOGLCD and #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER but it give me error. I have already install library U8glib. Thank you you dont want to uncomment doglcd since that i...