Page 5 of 6

Re: Show your printer(s)

Posted: Thu Nov 16, 2017 3:00 am
by lowfat
mgalamba wrote:
Thu Nov 16, 2017 2:05 am
Thanks to Hewlett Packard & Epson..... Mega+RAMPS. ...


Thanks to Tom and his excellent guides!!!!!!
Currently working on a New design. ... from scratch
How much did you spend on that? How noisy are those DC motors? Are they a closed loop system? Can you get decent speeds out of it?

Re: Show your printer(s)

Posted: Thu Nov 16, 2017 4:32 am
by fred2088
TinyBoy 2 E10 on the plane ...

Image

Image

Re: Show your printer(s)

Posted: Thu Nov 16, 2017 8:32 am
by Bigwerth
I have a Tevo Tarantula nothing special

Re: Show your printer(s)

Posted: Thu Nov 16, 2017 4:26 pm
by skmskm
My 3D printer one meter tall Delta.
Field: 400mmx300mm W/H
Board MKS SBASE V1.3
Made it my self from zero, most parts are my own project except part colling and some standard 3D printer parts.
DSCF0009.JPG
DSCF0009.JPG (4.05 MiB) Viewed 3732 times
Last print:
23334103_1611020818943910_8192566572696367137_o.jpg
23334103_1611020818943910_8192566572696367137_o.jpg (395.92 KiB) Viewed 3732 times

Re: Show your printer(s)

Posted: Thu Nov 16, 2017 7:36 pm
by mgoodfel
My DIY printer from 2015. Thinking of rebuilding it now that I've learned a bit about printers.

Image

Re: Show your printer(s)

Posted: Thu Nov 16, 2017 9:22 pm
by JohnArild
It is still a work in progress, but here is my custom clone of the TAZ6. It prints fairly good although it is a bit flimsy until I get the aluminium corner brackets.
IMG_E1298 (1).jpg
IMG_E1298 (1).jpg (301.15 KiB) Viewed 3714 times

Re: Show your printer(s)

Posted: Thu Nov 16, 2017 11:07 pm
by david.roy
Forgive the messy garage, but I'm using the Prusa I3 Mk2 with a custom built enclosure that is total overkill. I left room for larger printers in case I wanted to upgrade down the line. Never underestimate the decibels put out by the MK2 in an enclosure without anything to absorb the sound.
Printer.jpg
Printer.jpg (865.96 KiB) Viewed 3708 times

Re: Show your printer(s)

Posted: Fri Nov 17, 2017 1:33 am
by mgalamba
lowfat wrote:
Thu Nov 16, 2017 3:00 am
mgalamba wrote:
Thu Nov 16, 2017 2:05 am
Thanks to Hewlett Packard & Epson..... Mega+RAMPS. ...


Thanks to Tom and his excellent guides!!!!!!
Currently working on a New design. ... from scratch
How much did you spend on that? How noisy are those DC motors? Are they a closed loop system? Can you get decent speeds out of it?
I spend u$s60 aprox.... for Mega+ramps+5A4988, inductive sensor, simil E3d v6 (with normal and volcano pack of nozzles), mk8 remote extruder with bowden PTFE, heatbed 200x300mm....All cheap chinese of course!!!
The motors are all steppers from old Epson inkJet printers (Stylus color 800, C62, etc.)....
X axis ... Stylus color 800 (as is) with stepper, belt, etc :D .......
Z and Y rods and supports (beatifull and shiny chromed bars) from HewlletPackard DJ 3550 (I think, not sure).... (DC motors saved for other projects)...
All "wood" exedent from kitchen furniture....
When was able to print, i added the 2º rod to the X axis and change the corners of the Y axis as can see in the pictures (previusly in wood)...
It´s not noisy, because have been improved with printed LMU8 in POM (Y axis), does not have any linear ball bearing....
Being Bowden, does not require high torque motors, so it works well up to 60mm/s, I have not tested faster because the structure is not very stable (the top of the printer moves too much), and the table where it is It does not help (very unstable too)....

best regards

Re: Show your printer(s)

Posted: Sun Nov 19, 2017 3:50 pm
by umbyka
My DIY 2015 printer,with 1m3 build volume.

Re: Show your printer(s)

Posted: Wed Dec 13, 2017 3:29 am
by lowfat
Monoprice Mini

Image

Image

Image

Image